IPETRONIK interior simulation box is designed to simulate the passenger compartment for tests in recirculation mode (new, unused).

IPETRONIK

Type: Interior Simulation Box

Technical Data and Description of the System:

IPETRONIK Interior Simulation Box (new and unused)

The interior simulation box is designed to simulate the passenger compartment for tests in recirculation mode.
It has a variable interior volume of 1.8 to 4m³.
The exhaust air volume flow from the front evaporator or air conditioning unit is regulated and directed into the interior.
Only rear evaporators installed in the passenger compartment are tested with the interior simulation box.
The insulated housing is mounted on an aluminum profile frame with wheels.
A light is installed in the chamber.

The box is secured against overheating by a safety thermostat (Esti).

If the permissible temperature is exceeded, a glass cartridge in the ESTI is destroyed. The system will stop.
(TRIGGER TEMPERATURE: 80°C)

Technical Data of the Insulation Chamber:

Dimensions:

Outside: Width 1,860 mm Depth 2,360 mm Height 1,360 mm
Inside: Width 1,700 mm Depth 2,200 mm Height 1,200 mm

Insulation:

80 mm polyurethane rigid foam, CFC-free foamed, U-value 0.27 W/m²K, building material class B1 according to DIN 4102

Technical Data and Description of the System:

Connection: Tongue-and-groove system with foamed-in eccentric locking hooks.

Surfaces:

Both sides: 0.8 mm stainless steel sheet 1.4301, polished, grain 320

Floor Design:

2.0 mm stainless steel sheet 1.4301, SM diamond pattern, slip-resistant,
floor continuously raised at 90° (approx. 15 mm), floor plate flush with wall plate,
pressure distribution plate made of plywood, 1,500 N/ rubber wheel load capacity (contact area > 4 cm²),
30,000 N/m² surface load, floor joints completely welded, welded stainless steel pipe as floor drain,
led down through the floor

Chamber Door:

Hatch door, single-leaf, 800 x 1200 mm in the clear, DIN left, heated door frame (230 V),
heating bands silicone-free, 4-sided sealing profile made of EPDM,
pressure lever lock, lockable, emergency release,
heated viewing window, 500 x 500 mm, triple-glazed,
surface heating (230 V), frame heating (230 V), heating regulated on-site,
silicone-free edge trim

Movable Wall:

1680 x 1180 mm, 80 mm polyurethane rigid foam, both sides 0.8 mm stainless steel sheet 1.4301,
polished, grain 320, with protective film, closed with sheet metal on the other side

(The rear wall is manually infinitely adjustable for volume change)

Recirculation System:

For temperature control, a heat exchanger (Systemair) for indirect temperature control is installed in the recirculation duct.
The air is circulated by a radial pipe fan (Cosmo), heating is done via an integrated electric heater in the brine circuit (Türk and Hillinger).
The heaters are continuously monitored by temperature sensors and limiters (Türk and Hillinger, Johnson Controls).
The cooling is done via a secondary brine circuit with pumps (KSB) and a 3-way valve (Belimo).Installed electrical heating power 1 * 6kW.
The mixing ratio is 50% water / 50% ethylene glycol.

Power Supply from Station: =TME2++AS-QF21
Operating Voltage: 400V
Power: 17kW
Rated Current: 33A
Fuse: 35A
Control Voltage: 24V DC / 24V AC / 230V AC
PLC System: S7 300

Condition: used

Scope of Delivery: (See Image)

(Changes and errors in the technical data are reserved!)

We would be happy to answer any further questions by phone.