Netzsch Gabo Component and DMA Test System EPLEXOR 6000

Netzsch Gabo

 Here we offer a component and DMA test system .

The new EPLEXOR® 6000/8000 N systems are tailored for applications in component and DMA testing.
Forces from a few mN to the kN range, temperatures from -150°C to 1500°C
and displacements of up to 100 mm can be achieved.

Gabo offers the complete spectrum of dynamic elastomer and polymer testing systems.
The instruments can be equipped with a moisture generator and an autosampler system for tensile, compressive, bending, and shear modes.

Measurement of viscoelastic material properties depending on temperature, frequency, and mechanical load

Testing systems of the EPLEXOR® model series enable the mechanical characterization of a wide range of different materials:
From adhesives, plastics, elastomers, and polymers to composites, metals, glasses, ceramic materials,
biomaterials, and food to liquids.

Areas of application include:

- DMTS/DMTA/DMA
- Analysis of viscoelastic material properties
- Dynamic material testing
- Dynamic fatigue testing
- Dynamic component testing
- Rheology

The method of Dynamic Mechanical Spectroscopy (DMTS/DMTA or DMA) uses forced mechanical vibrations to deform the test specimens.
The samples can be subjected to tensile, compressive, bending, shear, and other stresses.

The device series meets the requirements of the following standards:

- DIN 53513
- DIN 53533
- ISO 4664
- ISO 4666/3
- ISO 4666/4
- ISO 6721/1
- ISO 6721/4
- ISO 6721/5
- ISO 6721/6
- ASTM D 623
- ASTM D 4065
- ASTM D 4473
- BS 903 Part A50
- JIS K 6265

NETZSCH GABO Instruments GmbH presents the EPLEXOR® 6000/8000 N devices, a new high-force series for dynamic material testing.
The stationary devices achieve maximum forces of up to 6 kN or 8 kN and displacements of up to 100 mm.

The EPLEXOR® 6000/8000 N model series is universally applicable and designed for a variety of applications in material and component testing.

A wide selection of different sample holders expands the testing possibilities to a variety of new materials and sample geometries.

Depending on the configuration, DMTA measurements, static and dynamic component tests, fatigue tests, heat build-up tests,
rolling resistance determinations, and much more can be performed.

Different temperature chambers from -150°C to +1500°C, a climate generator that allows defined humidity levels from 5% rF to 90% rF,
material tests in liquids or under inert or flushing gas influence are part of the optional product range.

As with all models in the high-end series, two independent drive systems (servo drive and electrodynamic vibration drive)
are used here, which can be combined as needed depending on the application.

Specifications

Force range: ±3000N (6000 N)**

Dynamic elongation: ±1.5 mm

Static elongation: up to 50 mm

Frequency range: 0.001 Hz - 100 Hz

Temperature: RT to 500 °C

*Maximum elongation depends on the sample, sample holder, and frequency.
** Peak force

Included accessories:

PC including Eplexor 8 software, clamping device for hydraulic high-force tensile for forces above 1000 N

Force measuring cells: 1x 500 N, 1x 1,500 N, 1x 5,500 N, 1x 10,000 N

Commissioning is carried out by the buyer.
Due to the change of location, a recalibration must be performed. This is done by the buyer.

Machines are ready for operation, in impeccable condition, and the current model.

Condition: used

Scope of delivery: (See image)

(Changes and errors in the technical data are reserved!)
 
We would be happy to answer any further questions by phone.

Written orders can be placed via email or fax